Max 232
Features
- RS-232 Bus-Terminal ESD Protection Exceeds
±15 kV Using Human-Body Model (HBM) - Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU V.28 Standards
- Operates With 3-V to 5.5-V VCC Supply
- Operates up to 250 kbit/s
- Two Drivers and Two Receivers
- Low Supply Current: 300 µA Typical
- External Capacitors: 4 × 0.1 µF
- Accepts 5-V Logic Input With 3.3-V Supply
- Alternative High-Speed Terminal-Compatible Devices (1 Mbit/s)
- SN65C3232 (–40°C to 85°C)
- SN75C3232 (0°C to 70°C)
₨100
CompareProduct Description
The MAX3232 device consists of two line drivers, two line receivers, and a dual charge-pump circuit with ±15-kV ESD protection terminal to terminal (serial-port connection terminals, including GND). The device meets the requirements of TIA/EIA-232-F and provides the electrical interface between an asynchronous communication controller and the serial-port connector. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. The devices operate at data signaling rates up to 250 kbit/s and a maximum of 30-V/µs driver output slew rate.
Based on 0 reviews
Be the first to review “Max 232”
You must be logged in to post a review.
Related products
-
Analog/Digital Converters, Tools & Kits
LTC1871 DC-DC 3.5-30V 6A 100W Adjustable High Power Boost Power Module Step Up Board Converter 2 Way Display LED Voltmeter
Analog/Digital Converters, Tools & KitsLTC1871 DC-DC 3.5-30V 6A 100W Adjustable High Power Boost Power Module Step Up Board Converter 2 Way Display LED Voltmeter
Input voltage range: 3.5V-30V(Note: 30V is the maximum voltage, when use please make sure input lower than 30V, otherwise will burn out.)
Output voltage range: 3.5V-30V (boost mode, the input must be less than or equal to the output voltage)
Maximum input current: 10A (peak current)
Continuous Current: 6A
Size: 67cm(L) * 42cm(W) * 18cm(H)
Output power: Max 100W {Note: according to the law of conservation of power, computation under the condition of rated output current: Uin*Iin*efficiency =Uout*Iout(Uin:input voltage, Iin:input current)}
Weight: 35g
Color: Red
Voltmeter Accuracy: ± (5 ‰ + 1 digit)
Static power consumption:Typical about 15mA(With the input voltage, output voltage and the color is closely related to the digital pipe. The actual current there is a deviation)
IN +: Positive Input, IN-: Negative Input. OUT +: Positive output, OUT-: Negative output.SKU: n/a -
Analog/Digital Converters
DAC0800 Digital to Analog Converter
Features
- Fast Settling Output Current: 100 ns
- Full Scale Error: ±1 LSB
- Nonlinearity Over Temperature: ±0.1%
- Full Scale Current Drift: ±10 ppm/°C
- High Output Compliance: −10V to +18V
- Complementary Current Outputs
- Interface Directly with TTL, CMOS, PMOS and Others
- 2 Quadrant Wide Range Multiplying Capability
- Wide Power Supply Range: ±4.5V to ±18V
- Low Power Consumption: 33 mW at ±5V
- Low Cost
SKU: n/a -
Analog/Digital Converters
ADC0804 Analog to Digital Converter
Features of ADC0804:
- 0V to 5V analog input voltage range with single 5V supply
- Compatible with microcontrollers, access time is 135 ns
- Easy interface to all microprocessors
- Logic inputs and outputs meet both MOS and TTL voltage level specifications
- Works with 2.5V (LM336) voltage reference
- On-chip clock generator
- No zero adjust required
- 0.3[Prime] standard width 20-pin DIP package
- Operates ratio metrically or with 5 VDC, 2.5 VDC, or analog span adjusted voltage reference
- Differential analog voltage inputs
SKU: n/a
There are no reviews yet.