Arduino
Showing 1–15 of 32 results
-
-
Arduino, Raspberry Pi
16-Channel 12-bit PWMServo Driver – I2C interface – PCA9685 for Arduino Raspberry Pi DIY Servo Shield
Arduino, Raspberry Pi16-Channel 12-bit PWMServo Driver – I2C interface – PCA9685 for Arduino Raspberry Pi DIY Servo Shield
he PWM driver board uses the I2C method, so only four lines can be connected to the Arduino device:
“Classic” Arduino pin mode:
+ 5v -> VCC
GND -> GND
Analog 4 -> SDA
Analog 5 -> SCL
Old Mega pin way:
+ 5v -> VCC
GND -> GND
Digital 20 -> SDA
Digital 21 -> SCLSKU: 950 -
LCDs
2.4 INCH TFT LCD FOR ARDUINO
- 2.4″ diagonal LCD TFT display
- 240×320 resolution
- 5V compatible! Use with 3.3V or 5V logic
- Onboard 3.3V 300mA LDO regulator
- 8 bit digital interface, plus 4 control lines
- 4-wire resistive touchscreen
- Uses digital pins 5-13 and analog 0-3. That means you can use digital pins 2, 3 and analog 4 and 5. Pin 12 is available if not using the microSD
SKU: n/a -
Arduino
3’2 Inches TFT LCD Arduino
Features:
- Support Arduino Mega2560 Directly inserted
- With Full-angle IPS TFT panel
- OnBorad level conversion chip for 5V/3.3V MCU
- Compatible with 3.3/5 V operation voltage level
- Compatible with Arduino-Series development Board.
- (Please notice:This Screen is not touch screen)
- Provided 12-examples with Arduino ,3-examples with STM32
- With SD Card Socket
- With SPI FLASH circuit
SKU: n/a -
Arduino
43A H Bridge Drive PWM For Arduino Semiconductor BTS7960B
This driver uses Infineon chips BTS7960 composed of high-power drive full H-bridge driver module with thermal over-current protection. Double BTS7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High-current 43A
SKU: n/a -
Arduino, Modules/Motors
5A Monophase Active Output AC Current Transformer Module For Arduino
1, On-board precision micro-current transformer
2, On-board high-precision op-amp circuit, to do accurate sampling and appropriate compensation and other functions to signal
3, The module can measure AC current within 5A, corresponding output analog can be adjusted
4, Under ideal conditions, the input voltage VCC is 3-35V, according to the potentiometer (adjust the amplification ratio, amplification range 0-100 times) to adjust the required output voltage, but the output (OUT) of the maximum voltage does not exceed 1 / 2 VCC.
5, The output signal is the AC voltage signal, and the output signal voltage does not exceed the maximum 1 / 2VCC.
6, PCB board size: 38 (mm) x 18.5 (mm)SKU: n/a -
Arduino, Modules/Motors, Raspberry Pi
6-Digit 8 Segment Tube LED Display Module TM1637 for Arduino Raspberry PI
Arduino, Modules/Motors, Raspberry Pi6-Digit 8 Segment Tube LED Display Module TM1637 for Arduino Raspberry PI
– Using CMOS technology
– Display mode (6-Digit 8 Segment), support a total of positive digital tube output
– Key scan (8X2bit), enhanced anti-jamming key recognition circuit
– Gray scale adjustment circuit (duty cycle 8 adjustable)
– Two-wire serial interface (CLK, DIO)SKU: n/a -
Arduino, Modules/Motors
AC Voltage sensor module ZMPT101B 250V Voltage transformer module Arduino
- Measure within 250V AC
- Onboard micro-precision voltage transformer
- Analog output corresponding quantity can be adjusted.
- Good consistency, for voltage and power measurement
- Very efficient and accuracy
SKU: n/a
